Quick Installer Summary
Choosing between 22mm and 28mm copper press fittings comes down to design temperature drop (ΔT), water velocity limits (max 1.0–1.5 m/s per CIBSE Guide C), and total index circuit pressure drop. While 22mm copper easily carries up to 24–28 kW on a high-temperature gas boiler (ΔT = 20K), its capacity drops to just 6–7.5 kW on a low-temperature Air Source Heat Pump (ΔT = 5K). For any heat pump above 7 kW or commercial boiler primary above 28 kW, upgrading to 28mm M-profile copper press fittings is mandatory to prevent flow-rate faults, pump cavitation, and short cycling.
- 22mm Copper (ID 20.2mm): Max ~19–22 L/min at 1.0 m/s | Ideal for domestic boilers (≤28 kW) & 5–7 kW heat pumps.
- 28mm Copper (ID 26.2mm): Max ~32–38 L/min at 1.0 m/s | Mandatory for 8–16 kW heat pumps, unvented primaries & plant rooms.
- Hydraulic Advantage: Stepping up from 22mm to 28mm increases cross-sectional bore area by 68% and cuts friction pressure drop by over 70%.
For decades, UK domestic heating engineers defaulted to 22mm copper primary pipework for almost every gas boiler and hot water cylinder. However, the rapid adoption of Air Source Heat Pumps (ASHP), high-output system boilers, and multi-zone underfloor heating manifolds has changed hydraulic sizing rules completely.
Undersizing primary pipework by a single nominal diameter—using 22mm where 28mm is hydraulically required—causes high-pitched velocity noise, premature erosion corrosion in copper bends, failed heat pump defrost cycles, and nuisance flow-switch lockouts. This technical guide breaks down the exact CIBSE Guide C fluid dynamics comparing 22mm and 28mm M-profile copper press fittings so you can size plant rooms and heat pump primaries with zero guesswork.
The Hydraulic Physics: Why 6mm Extra Diameter Cuts Friction by 70%
On paper, stepping up from 22mm copper tube (BS EN 1057 Table X, 0.9mm wall, 20.2mm internal bore) to 28mm copper tube (0.9mm wall, 26.2mm internal bore) looks like a modest 27% increase in diameter. In fluid mechanics, however, pipe capacity scales with the square of the radius, while pressure drop scales inversely with the fifth power of the internal diameter (Darcy–Weisbach friction equation):
In practical site terms, moving from 22mm to 28mm copper:
- Increases internal cross-sectional area from 320 mm² to 539 mm² (a +68.4% jump in water volume).
- Reduces water velocity at a 25 L/min heat pump flow rate from 1.30 m/s (noisy, high friction) down to a whisper-quiet 0.77 m/s.
- Slashes linear friction head loss from roughly 650 Pa/m down to 180 Pa/m, allowing standard ErP 6m/7m circulation pumps to hit design flow without maxing out electrical draw.
CIBSE Guide C Comparison: 22mm vs 28mm Flow Rates & kW Capacity
To keep domestic and commercial heating systems silent and protect copper walls from impingement attack, CIBSE Guide C recommends keeping water velocity below 1.0 m/s in occupied domestic spaces (and max 1.5 m/s in plant rooms). Compare the maximum thermal kW capacity of 22mm vs 28mm copper across both gas boiler (ΔT = 20K) and heat pump (ΔT = 5K) operating regimes:
| Hydraulic Parameter | 22mm Copper (BS EN 1057) | 28mm Copper (BS EN 1057) |
|---|---|---|
| Internal Bore Diameter (ID) | 20.2 mm | 26.2 mm |
| Max Flow Rate @ 1.0 m/s | 19.2 L/min (0.32 kg/s) | 32.3 L/min (0.54 kg/s) |
| Max Heat Pump Output (ΔT = 5K) | 6.7 kW | 11.3 kW (up to 16 kW @ 1.4 m/s) |
| Max Condensing Boiler Output (ΔT = 20K) | 26.8 kW | 45.2 kW |
| 90° Press Elbow Equiv. Pipe Loss | 0.78 m (ζ = 1.40) | 0.95 m (ζ = 1.30) |
| M-Profile Pipe Insertion Depth | 21 mm | 23 mm |
Why Air Source Heat Pumps Fail on 22mm Primaries
A 12 kW Air Source Heat Pump (such as a Vaillant aroTHERM plus, Daikin Altherma, or Grant Aerona) operates at a 5°C temperature differential (ΔT) to maximise Seasonal Coefficient of Performance (SCOP). Because ΔT is four times smaller than a gas boiler, the heat pump must move four times more water per kilowatt—requiring roughly 34.4 litres per minute.
Forcing 34.4 L/min through 22mm copper pushes water velocity to 1.79 m/s, generating over 1,100 Pa/m of friction loss. Add eight 90° bends, a magnetic filter, and a 3-port diverter valve, and total circuit resistance easily exceeds the heat pump’s internal circulation pump head. The result is an immediate Low Flow / High ΔT fault code during commissioning. Running the primary flow and return in 28mm M-profile copper press drops velocity to 1.06 m/s and guarantees trouble-free MCS sign-off.
Stock Up on 22mm & 28mm Press Fit Trade Packs
Save up to 15% on your next heat pump or plant room install. Shop our WRAS-approved, BS EN 1254-7 certified 22mm & 28mm Copper M-Profile Press Fit 90° Elbows (Pack of 30) and full contractor combo boxes.
Shop 22mm & 28mm 90° Elbows → Shop 28mm 70pc Combo Pack →When to Stick with 22mm vs Step Up to 28mm
Choose 22mm Copper Press Fittings When:
- Piping standard domestic combi or system boilers up to 24–28 kW at ΔT 20K.
- Running secondary distribution mains feeding 15mm radiator drops across a 3–4 bedroom house.
- Installing compact 5 kW to 7 kW monobloc heat pumps with short (<6m) primary runs.
- Stocking your van for everyday domestic cylinder swaps using our 22mm Press Fit Water Fittings Combo Pack (130 Pieces).
Choose 28mm Copper Press Fittings When:
- Installing any 8 kW to 16 kW Air Source Heat Pump primary flow and return circuit.
- Piping high-output system boilers (30 kW to 45 kW) into low-loss headers or buffer vessels.
- Supplying high-flow unvented hot water cylinders (250L–300L+) serving multiple rainfall showers simultaneously under G3 Building Regulations.
- Executing flame-free commercial plant room retrofits where hot-works permits are prohibited and speed of 28mm M-profile crimping saves 60%+ labour time over end-feed brazing.
Frequently Asked Questions
Do air source heat pumps always require 28mm copper pipework?
No — heat pumps do not always require 28mm pipework; sizing depends strictly on kW heat load, design ΔT (typically 5K), and total index circuit run length. For compact 5 kW to 7 kW monobloc heat pumps requiring under 20 L/min of flow, 22mm copper tube (ID 20.2mm) stays safely below the CIBSE Guide C 1.0 m/s velocity limit. However, for 8 kW to 16 kW heat pumps requiring 23–45 L/min, stepping up to 28mm copper press fittings (ID 26.2mm) is essential to prevent high friction head loss, pump cavitation, and low-flow lockouts.
How many kW can 22mm vs 28mm copper pipe carry on a heat pump vs gas boiler?
At a quiet 1.0 m/s water velocity (CIBSE Guide C), 22mm copper carries up to 6.7 kW on a heat pump (ΔT 5K) or 26.8 kW on a gas boiler (ΔT 20K), whereas 28mm copper carries up to 11.3 kW on a heat pump (ΔT 5K, rising to 16 kW at 1.4 m/s) or 45.2 kW on a gas boiler (ΔT 20K). Because heat pumps run at a 4× smaller temperature differential than condensing boilers, they must circulate 4× more water volume per kilowatt.
Can I keep my existing 22mm primary pipes when upgrading from a gas boiler to a heat pump?
Yes, you can retain existing 22mm copper primaries if your property’s calculated heat loss is 7 kW or below and the hydraulic index run is short. If your heat loss calculation requires an 8 kW–16 kW heat pump, keeping a 22mm bottleneck between the outdoor unit, buffer vessel, and cylinder forces water velocity above 1.5 m/s, causing pipe noise and poor Seasonal Coefficient of Performance (SCOP). In those cases, upgrade the primary backbone to 28mm using flame-free 28mm M-profile copper press elbows and tees.
What happens if 22mm pipework is undersized for a heat pump or plant room?
Undersized 22mm pipework causes excessive flow velocity (>1.5 m/s), audible rushing noise, accelerated internal erosion corrosion at 90° bends, and high pump electrical draw. When friction pressure drop exceeds the heat pump’s built-in circulation pump head, the unit fails to reach minimum flow rate, triggering repeated Low Flow / High ΔT fault codes and aborted defrost cycles.
What happens if primary heating pipes are oversized (using 28mm where 22mm is enough)?
Oversizing short domestic runs to 28mm increases material cost, fitting footprint, and standing water volume (thermal mass), which can slow down system warm-up response if velocities drop too low (<0.3 m/s) to purge air pockets effectively. Always size primary circuits from a room-by-room BS EN 12831 heat loss and hydraulic flow calculation rather than blanket rules of thumb.
Are MEP Stock 22mm and 28mm copper press fittings compatible with Viega, Geberit, and Rothenberger press tools?
Yes — MEP Stock 22mm and 28mm copper press fittings use the universal BS EN 1254-7 M-Profile contour and crimp directly with Rothenberger Romax, Novopress, Milwaukee M18 Force Logic, Klauke, and REMS M-profile jaws. Dimensionally and technically, they are direct WRAS-approved trade equivalents to Geberit Mapress Copper and Conex Bänninger >B< Press (note: Viega Profipress uses V-profile jaws and must not be mixed with M-profile jaws).
Where can I buy WRAS-approved 22mm and 28mm copper press fittings in bulk trade packs?
You can order WRAS-approved, BS EN 1254-7 certified 22mm and 28mm M-profile copper press fittings directly from MEP Stock in singles, trade Packs of 10, 20, and 30, or pre-sorted contractor combo boxes. Buying in trade Packs of 30 on high-usage fittings like our 22mm and 28mm Copper M-Profile Press Fit 90° Elbows significantly lowers your per-fitting cost compared to standard merchant counter singles.
What is the most cost-effective way to stock 22mm and 28mm press fittings for heat pump and boiler installs?
For regular boiler swaps, unvented cylinders, and Air Source Heat Pump primaries, pre-sorted contractor combo packs offer the lowest unit cost and eliminate part-picking delays. MEP Stock offers both the 22mm Press Fit Water Fittings Combo Pack (130 Pieces) and the 28mm Press Fit Water Fittings Combo Pack (70 Pieces) containing 90° elbows, equal tees, straight couplings, and street elbows.
How do I transition cleanly between 28mm primary pipework and 22mm secondary circuits?
Use BS EN 1254-7 M-profile copper press reducing tees (28mm × 28mm × 22mm or 28mm × 22mm × 28mm) and concentric press reducers to step down from 28mm primaries to 22mm distribution loops without turbulence or soldered joints. Browse the complete MEP Stock Press Fit Water Fittings range for matching 28mm-to-22mm reducers, reducing tees, and isolation valves.
